control vertex造句
例句與造句
- A mst based clustering method with controlling vertexes
一種帶控制節點的最小生成樹聚類方法 - The following flags control vertex processing behavior for the hardware abstraction layer ( hal ) and reference devices
下面的標識為硬件抽象層和引用設備控制頂點處理的行為。 - The first algorithm gives unique result unaffected by the handling order of points concerned , and it calculates the control vertexes at once without estimation and correction
第一種算法的特點是重建結果不依賴于頂點的處理順序，不需要進行控制頂點的初估及修正，可使各控制頂點的計算一次完成。 - Two methods are given to get the control vertexes , by making the two approximated helix segments gc2 continuous at their connecting point and leting the theoretical helix and the approximated one coincident at five points respectively
對于其控制頂點的確定給出了兩種方法。方法一，使逼近螺線在連接點處gc ~ 2連續，得到的逼近螺線與理論螺線在兩端點及中心理誤差為零。 - A fairing method based on energy me thod for cubic b - spline curves is presented . since only local control vertices ar e modified , this method , compared with energy method , not only makes the c omputation faster , but also makes the changes in shape of curve less
4 )研究了b樣條曲線光順的問題，在傳統能量法的基礎上提出了b樣條曲線的一種光順?lè)椒?。該方法通過對局部控制頂點的修改來進行曲線光順。 - It's difficult to find control vertex in a sentence. 用control vertex造句挺難的
- The general idea behind the second one is approximation . the control mesh is subdivided until the error between the control vertices and corresponding subdivision surface is less than a given threshold . then the vertices substitute those points on the surface approximately . the last step is to calculate offset point for every vertex and connect them to form an offset surface
第二種算法采用逼近思想，首先通過對控制網格進行細分，當控制頂點和細分曲面的距離滿足一定誤差要求時，近似用控制頂點代替細分曲面上的點，然后對各個頂點分別求等距點。 - It offers the idea according to problem faced , considering the good character of the ends , the ajusted cubic b - spline curve is used to fit ship lines . it finds out the control vertexs according to a sequence of given points , and then , through particular formula , each point in the curve could be worked out . it smoothes lines with the method based on small - paramter
針對面臨的問題，提出了自己的思路，在數學計算方法上，由于三次準均勻b樣條曲線良好的端部性質，這里用它來擬合船舶型線，首先根據所給的初步型值求出其控制頂點，然后根據相關公式進行插值便能得到曲線上的所有插值點。 - During the past decades , some researchers , such as : bezier , kj . versprile , deboor and cox , etc . had made great progress in the filed of constrained b - spline curve and surface fitting . in this article the method of constrained b - spline curve was introduced , which is used to figure out the control vertexes . using this interpolation method we can calculate every points of a uniform b - spline
并且分析了在各種端點情況下，在重節點的情況下，如何反算控制多邊形的頂點；如何在求出控制多邊形頂點之后，插值計算b樣條擬合曲線上的每一點；并通過結合雙尾船的型線，采用visualc + +和autocad2002為平臺，分別編制了相應的軟件，對提供的型值做出繪圖處理，取得了良好的效果。